|
|
| Model |
TGI-250kN |
TGI-100kN |
TGI-50kN |
TGI-10kN |
TGI-5kN |
TGI-1kN |
TGI-500N |
TGI-200N |
| Maximum test force |
250 kN |
100 kN |
50 kN |
10 kN |
5 kN |
1 kN |
500 N |
200 N |
| Test force measure -ment range *1) |
0.1N~
250kN |
0.1N~
100kN |
0.1N~
50kN |
0.1N~
10kN |
0.1N~
5kN |
0.1N~
1kN |
0.1N~
500N |
0.1N~
200N |
| Test space |
Tensile / compression testing beneath the movable crosshead.
(A model is available allowing tensile testing above the movable crosshead (Optional).) |
| Loading method |
Constant-speed strain loading with highly accurate AC servo motor and backlash-free precise ball screw. |
| Cross head speed / permissible test force |
Within the max. test force over the entire speed ranges. |
| Test force range |
2 methods:
AUTO: (accuracy guranteed for 1/1 to 1/250 of load cell capacity)
100: (accuracy guranteed for 1/100 to 1/1 000 of load cell capacity) |
| Test force display |
5-digits digital display ±99,999
AUTO range: Resolution 1/5000, test force reduction increase/decrease, Full scale display, and automatic switching of decimal point position and display unit.
100 range: Resolution 1/10000
* Test force display varies depending on the load cell provided. |
| Test force measuring accuracy (Guaranteed accuracy range) |
Standard accuracy : ±1 % of indicated value
(1/1 to 1/1000 of load cell capacity)
High accuracy : ±0.5% of indicated valeu (Optional)
(1/1 to 1/1000 of load cell capacity)
* Test machine must be in location free of vibration |
| Applicable standard |
JIS B 7721 Class 1 or Class 0.5 and ISO7500-1 Class 1 or Class 0.5 |
| Effective test width (Note 2) (mm) |
600 |
600 |
420 |
430 |
| Cross head stroke (mm) |
1 550 |
1 350 |
1 015 |
1 090 |
| Maximum mounting space (mm) |
1 690 |
1 555 |
1 165 |
1 160 |
| Tensile stroke (Note 3) (mm) |
620 |
850 |
470 |
710 |
820 |
870 |
890 |
910 |
| Crosshead speed |
0.000 5 to 500 mm/min
0.1 to 500 mm/mincan be set in 0.1 mm/min incliments. Below this, can be set in 9 steps: 0.05, 0.03, 0.02, 0.01, 0.005, 0.003, 0.002, 0.001, and 0.0005. |
0.000 5 to 1 000 mm/min
0.1 to 1 000 mm/min; can be set in
0.1 mm/min increments. Below this, can be set in 9 steps: 0.05, 0.03, 0.02, 0.01, 0.005, 0.003, 0.002, 0.001, and 0.0005. |
| Crosshead speed accuracy |
±0.1 % over entire speed range |
| Return speed |
Can be set as required between 0.1 mm/min and 750 mm/min |
Can be set as required between 0.1 mm/min and 1 500 mm/min |
| Speed setting method |
Manual: Numeric input via control panel
When using data processing software: Automatically set in accordance with test conditions created. |
| Manual speed |
3 speeds (HIGH/MIDDLE/LOW); each freely settable |
| Test mode |
Single and cycle (Combination of test force and position)
Optional: Creep, Automatic loading |
| Test force display |
5 digit digital display ±99 999
Auto range: Resolution 1/5 000, test force reduction increase/decrease, full scale display, and automatic switching of decimal point position and display units
100 range: Resolution 1/10 000 * Test force display varies depending on the load cell provided. |
| Movable crosshead position display |
6 1/2-digit digital display ±1999.999 |
| Standard function |
| Load cell model & capacity |
：
|
Auto adjust |
| Load cell span |
：
|
Auto set for tension & compression
|
| Zero point |
：
|
One push |
| Position reset |
： |
One push |
| Sample rupture detection |
：
|
Selectable from stop, reverse and ignore |
| Rupture sensitivity |
：
|
Set as desired to 0.04 % to 99.00 % of test force |
| Test condition registration function |
：
|
10 conditions |
| Test force & position analog output |
：
|
DC0 ~ DC5 V (with scaling function) |
| Interface |
：
|
Conforms to USB interface 2.0/1.1 standard (B- type connector) |
|
| Options |
| Chuck adapter |
：
|
Lower chuck mounting adapter for tensile testing |
| Load cell |
：
|
for tension / compression type
(with universal joint, connect pin and compression plate
----------
for tensile type
(with universal joint and connecting pin)
----------
for compression type
(with for compression plate)
|
| Testing jig |
：
|
Former jig is attachable. |
| Displacement measuring function |
：
|
Strain input type |
| Test machine stand |
| Data processing software |
：
|
Standard (Tensile / compression / bending), Peeling, Cycle (One way, Both way),
Stress relaxation |
|
| External dimensions (WxHxD)(mm) |
1420 x 2406 x 894 |
1221 x 2192 x 720 |
900 x 1507 x 490 |
700 x 1583 x 523 |
700 x 1 583 x 513
(without level adjuster) |
| Approximate weight (kg) |
1 200 |
900 |
310 |
120 |
| Power supply voltage, Frequency |
3-phase AC200 V to 230 V+10 % to 15 %, 50/60 Hz |
Single phase AC100 V to 115 V+10% to -15%, 50/60 Hz |
| Power consumption (W) |
7.5 k |
2.9 k |
1.8 k |
750 |
400 |
| Operating temperature / humidity range |
Temperature 5 ℃ ~ 40 ℃,
Humidity 20 % ~ 80 %RH (with no condensation) |
- Note 1: Test force measurement range varies depending on the rated capacity of load cell used.
- Note 2: Testing machines are available with large effective width for models with maximum test force of 50 kN, 100 kN or 250 kN.
Note 3: Models are available with extended stroke.
|
Danh mục sản phẩm
